3 Account
4 Info
Max Protect Ultimate Nano Coat-R UNC-R 1,5 membranowa powłoka kwarcowa 30ml
  • Max Protect Ultimate Nano Coat-R UNC-R 1,5 membranowa powłoka kwarcowa 30ml
  • Max Protect Ultimate Nano Coat-R UNC-R 1,5 membranowa powłoka kwarcowa 30ml
Dostawa za darmo
Wyświetl koszt wysyłki

Max Protect Ultimate Nano Coat-R UNC-R 1,5 membranowa powłoka kwarcowa 30ml

UNC-R to pierwsza na świecie powłoka tworząca membranę gumową. Bardzo odporna na powstawanie swirli i water spotów, wyjątkowo błyszcząca o niesamowicie wysokiej odporności chemicznej.

389,00 zł
Max Protect
Zobacz wszystkie produktyMax Protect

Max Protect Ultimate Nano Coat-R 1,5
To najnowsze osiągnięcie specjalistów z Max Protect. Po pierwszej na świecie powłoce, która tworzy na lakierze gumową membranę, inżynierowie Max-Protect przygotowali alternatywę oznaczoną numerem 1,5, która dzięki spowolnieniu procesu wiązania powłoki, ułatwia aplikację w wyższych temperaturach (powyżej 20’C)

UNC-R 1,5 jest przy tym bardzo elastyczna, pozostawiona do zaschnięcia nie przypomina żadnegoinnego produktu, a jednocześnie zapewnia doskonałą ochronę przed mikrorysami, a także chemikaliami oraz działaniem twardej wody. Dzięki swojej strukturze potrafi maskować drobne defekty, takie jak wypiaskowania. Jedynym sposobem na usunięcie tego permanentnie wiążącego się z powłoką lakierniczą zabezpieczenia jest
polerowanie.
UNC-R 1,5 jest wymagająca w aplikacji i w celu zapewnienia idealnego wyglądu powierzchni, powinna być nakładana jedynie przez profesjonalistów.
Ponadto, w przeciwieństwie do zwykłego UNC-R, tę powłokę można warstwować.

Pojemność 30ml
Trwałość do 2 lat

For best results, paintwork should be machine polished before UNC-R Application. A fine polish is all that is necessary to prepare the surface for coating application. In case of a brand new car, or a car with paintwork in excellent condition, we recommend to polish by hand, or perform a very mild, final stage machine polish. Degreasing with Panel Wipe is recommended for best results, if not available, IPA or similar cleaners will do the job too.

UNC-R can be applied in a single layer only, so you won't be able to apply UNC-R + UNC-R, for example, however, you can apply it over a previous layer, or few layers, of UNC v1, this way achieving a multi layer coating.

We recommend using polishing compounds with minimum or no oils in content. Polishing compounds with waxes and high oil content should be avoided.

Important: It is very important to have good lighting in the place of application! In dim light you might not spot smears left behind and removing them later will be a lot more difficult. 

Good ventilation is a must to have and appropriate safety wear (Gloves, Glasses, Mask, etc.) should be worn.

Please make sure you have the following before UNC-R application:

1. Panel Wiper – not supplied
2. Ultimate Nano Coat-R
3. Silk Coat – not supplied (Optional)
5. Applicator Sponge – not supplied
6. Microfiber Towels – not supplied

UNC-R Application:

Attention: UNC-R flashes off very quickly (quicker than UNC v2), so work on smaller areas.

1. Open the UNC-R bottle and put the applicator sponge on top and shake it once. Move the sponge a bit and shake it again. Do it for 3-4 times till the sponge is slightly wet, but not soaked).
2. Put the sponge on the surface and apply the coating with short and quick movements. Don’t do circular movements. Keep applying till the whole panel is covered.
3. Once half a panel is covered (roof, bonnet), remove the coating immediately with a fresh microfiber cloth/ towel.
4. For smaller panels like wings and other small bits we recommend not waiting more than 30 seconds before removal.
5. Apply UNC-R on one panel at a time. Take extra care to look for marks/ smears left behind as removing them later will be more difficult.
6. Use 2 microfiber towels/cloths for excess removal.

Silk Coat is recommended however not necessary if the car is not leaving immediately after application in bad weather conditions.

Tips:

1. Always use new microfiber towels/cloths
2. The applicator sponge can not be re-used - always use new one.
3. Remember not to mix microfiber towels between different coatings (V1&R, etc.)
4. Use Silk Coat for maintenance – super easy to apply!
5. Above temperatures of +20c speed is necessity not a recommendation.

Specyficzne kody

Nikt nie dodał jeszcze opinii

Szukaj

You can try some popular tags here:

Account

No account?
Create one here
Korzystając z naszej strony wyrażasz zgodę na wykorzystywanie przez nas plików cookies. Możesz określić warunki przechowywania lub dostępu do plików cookies w Twojej przeglądarce. Akceptuj Więcej informacji Odrzuć